收藏本站
ADT7476
Step 4 ? PWM MIN for Each PWM (Fan) Output
PWM MIN is the minimum PWM duty cycle at which each
fan in the system runs. It is also the start speed for each fan
under automatic fan control once the temperature rises
above T MIN . For maximum system acoustic benefit,
PWM MIN should be as low as possible. Depending on the
fan used, the PWM MIN setting is usually in the 20% to 33%
duty cycle range. This value can be found through fan
validation.
100%
Example 1:
For a minimum PWM duty cycle of 50%,
Value (decimal) = 50/0.39 = 128 (decimal)
Value = 128 (decimal) or 80 (hex)
Example 2:
For a minimum PWM duty cycle of 33%,
Value (decimal) = 33/0.39 = 85 (decimal)
Value = 85 (decimal) l or 54 (hex)
Table 45. P WM  MINIMUM DUTY CYCL E REGISTERS
Register
0x64
0x65
Description
PWM1 Minimum Duty Cycle
PWM2 Minimum Duty Cycle
Default
0x80 (50%)
0x80 (50%)
PWM MIN
0x66
PWM3 Minimum Duty Cycle
0x80 (50%)
T MIN
0%
TEMPERATURE
Figure 54. PWM MIN Determines Minimum
PWM Duty Cycle
More than one PWM output can be controlled from a
single temperature measurement channel. For example,
Remote 1 temperature can control PWM1 and PWM2
outputs. If two different fans are used on PWM1 and PWM2,
the fan characteristics can be set up differently. As a result,
Fan 1 driven by PWM1 can have a different PWM MIN value
than that of Fan 2 connected to PWM2. Figure 55 illustrates
this as PWM1 MIN (front fan), which is turned on at a
minimum duty cycle of 20%, while PWM2 MIN (rear fan)
turns on at a minimum of 40% duty cycle. Note: Both fans
turn on at exactly the same temperature, defined by T MIN .
100%
PWM2
Note on Fan Speed and PWM Duty Cycle
The PWM duty cycle does not directly correlate to fan
speed in RPM. Running a fan at 33% PWM duty cycle does
not equate to running the fan at 33% speed. Driving a fan at
33% PWM duty cycle actually runs the fan at closer to 50%
of its full speed. This is because fan speed in %RPM
generally relates to the square root of PWM duty cycle.
Given a PWM square wave as the drive signal, fan speed in
RPM approximates to:
% fanspeed + PWM Duty Cycle 10 (eq. 5)
Step 5 ? PWM MAX for PWM (Fan) Outputs
PWM MAX is the maximum duty cycle that each fan in the
system runs at under the automatic fan speed control loop.
For maximum system acoustic benefit, PWM MAX should be
as low as possible but should be capable of maintaining the
processo r temperature limit at an acceptable level. If the
THERM temperature limit is exceeded, the fans are still
boosted to 100% for fail-safe cooling.
There is a PWM MAX limit for each fan channel. The
default value of this register is 0xFF and has no effect unless
PWM2 MIN
PWM1
it is programmed.
PWM1 MIN
0%
T MIN
TEMPERATURE
100%
PWM MAX
Figure 55. Operating Two Different Fans from
T MIN
a Single Temperature Channel
Programming the PWM Minimum Duty Cycle Registers
The PWM minimum duty cycle registers are 8-bit
registers that allow the minimum PWM duty cycle for each
output to be configured anywhere from 0% to 100%. This
allows the minimum PWM duty cycle to be set in steps of
0.39%.
PWM MIN
0%
TEMPERATURE
Figure 56. PWM MAX Determines Maximum PWM Duty
Cycle Below the THERM Temperature Limit
The value to be programmed into the PWM MIN register is
given by:
Value (decimal) = PWM MIN /0.39
http://onsemi.com
38
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ADT7490ZEVB BOARD EVALUATION FOR ADT7490
ADZS-21262-1-EZEXT BOARD DAUGHTER FOR ADSP-21262
ADZS-BF-EZEXT-1 BOARD DAUGHTER ADSP-BF533/561KIT
ADZS-BFAV-EZEXT BOARD DAUGHT ADSP-BF533,37,61KIT
ADZS-BFSHUSB-EZEXT BOARD DAUGHTER EZ EXTENDER
ADZS-BRKOUT-EX3 ADZS-BRKOUT-EX3
ADZS-SHAUDIO-EZEXT SHARC AUDIO EZ-EXTENDER
ADZS-WVGALCD-EX3 BOARD EXTENDER WVGA/LCD EI3
相关代理商/技术参数
ADT7481 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm
ADT7481ARMZ 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-001 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-1 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6
ADT7481ARMZ-1R7 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
ADT7481ARMZ-1REEL 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADT7481ARMZ-1REEL7 制造商:AD 制造商全称:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm
ADT7481ARMZ-1RL 功能描述:板上安装温度传感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor